50ft Drip Irrigation Kit, 8x5mm Tubing, Irrigation Equipment Set

$20.99
by Hiraliy

*As an Amazon Associate I earn from qualifying orders. This doesn't increase product cost to you.

View on Amazon

The Hiraliy Drip Irrigation Kit uses 50 feet of 1/4 inch tubing, 12 tees, and 12 adjustable staked emitters to water potted plants, raised beds, flower beds, and small garden areas. A solid brass splitter with butterfly valves attaches to standard 3/4 inch spigot threads and divides water into two independently controlled lines.

Each emitter twists from off to a slow drip or a spray, so you can tune water for containers of different sizes. Drip emitters respond strongly to water pressure, so set the spigot to a moderate flow or add a pressure regulator.

Specifications

  • Tubing: 50 feet of 1/4 inch tubing, with a 98.4 foot version offered
  • Splitter: Solid brass, two outlets with butterfly valves, 3/4 inch thread
  • Tees: 12 tee connectors
  • Emitters: 12 adjustable drip emitters with built in stakes
  • Emitter Settings: Off, micro drip, or spray
  • Setup: Push in fittings, user manual, and QR code installation video
  • Uses: Lawns, patio gardens, greenhouses, flower beds, and raised beds

Container and Raised Bed Watering on a Two Zone Timer

If you water a patio full of pots or a couple of raised beds by hand every day, this kit lets you stake an emitter in each pot or along each bed and run everything from one spigot. The brass splitter gives you two lines, which pairs naturally with a dual zone timer so pots and beds can water on separate schedules.

Keep each line short with a moderate number of emitters, and turn down the emitters closest to the splitter so water reaches the end. Plan and cut your own tubing lengths based on your layout rather than relying on preset measurements.

What to Expect from the Hiraliy Drip Irrigation Kit in Real Use

Verified Amazon purchasers praise the brass splitter and metal hose connector, and many report no leaks when installed properly. One owner who tried other kits came back to this one, expanding from 8 to 17 potted plants on a dual zone timer. Another ran 8 emitters over about 10 feet and turned down the nearest heads to push water to the last one.

Assembly takes patience. Dipping tubing ends in hot water for about 30 seconds makes connections easier, though it can still be hard on arthritic hands. High pressure can override emitter settings, so several owners throttle the faucet. The bigger complaint is tubing popping off fittings.

One owner had lines detach repeatedly, including while away on vacation, another found connections blowing in the second season after leaving tubing outdoors over winter, and a third saw an emitter arm pushed off by high pressure.

Real-world performance notes sourced in part from verified Amazon customer purchases.

Frequently Asked Questions

Do you need a pressure regulator for drip irrigation?

In most cases, yes. Household water pressure often runs well above what drip components are designed for, which can cause emitters to spray too hard and tubing to blow off fittings. A pressure regulator installed at the spigot, after a timer and backflow preventer, lowers pressure to a range drip systems handle reliably, typically around 25 to 30 PSI.

How do you keep drip tubing from popping off fittings?

Cut tubing ends straight and clean, warm them in hot water so they slide fully over the barbs, and push each connection all the way on. Lower the water pressure with a regulator or by partially closing the spigot. Replace stretched or cracked tubing ends by trimming them and reconnecting, and check connections after the first few watering cycles.

How do you winterize a drip irrigation system?

Before the first hard freeze, shut off and disconnect the system from the spigot. Remove end plugs and let water drain from every line, then disconnect the splitter, timer, and emitters and store them indoors. Coil tubing and store it in a garage or shed if possible, since freezing water and winter sun weaken plastic and fittings.